Interrupted in eddyPro 4.1 and metadata file

Environmental Forum Forums EddyPro Interrupted in eddyPro 4.1 and metadata file

This topic contains 3 replies, has 2 voices, and was last updated by  duydb.vrtc 5 years, 12 months ago.

Viewing 4 posts - 1 through 4 (of 4 total)
  • Author
    Posts
  • #1435

    duydb.vrtc
    Participant

    Dear Sir or Madam,!

    I use EddyPro 4.1 for my raw data but I have some problem in my results:

    – How can it not be interrupted on 16.02.2013?

    – What is my metadata file need to change to get the full out put?

    Thanks a lot and best regarads

    Duy Dinh

    #1745

    gerardo
    Participant

    Hello Duy Dinh,

    please note a couple of errors in the “input2.metadata” file:

    1. In “Metadata File Editor” >> “Raw File Description” there is a button called “Raw File Settings”. There, you need to enter “4” in the “Number of header rows”, because your raw files contains 4 header lines at the beginning.

    2. More importantly: in your metadata file, Column 13 is described as “LI-7500(A) Diagnostics”. This is wrong, because the file contain AGC at that column. Please note that, although AGC is a quantity provided for diagnostic purposes, it is different from the “LI-7500(A) Diagnostic”, which is an different, completely independent variable that can be collected from the LI-7500 analyzer. Please rename your Column 13 as “AGC”(you can type it in the variable field).

    3. Finally, note that units “g/m3” and “mg/m3” are available in the “Input unit” field of the “Raw file description table”, so you don’t need to provide the gain/offset information to get a proper conversion.

    Find attached a revised metadata file. Please let us know if this solved your problems.

    Thanks,

    Gerardo

    #1746

    duydb.vrtc
    Participant

    Hello gerardo,

    Thank you very much for your support. I have just run with your metadata file and It’s Ok with 4 may sample file (TOA5_CatTien_EC_2012_02_15_2300.dat -> TOA5_CatTien_EC_2012_02_16_0030.dat). However, The program has been interrupted when I try to run with more other file.

    Please run again with my 6 file (TOA5_CatTien_EC_2012_02_15_2300.dat -> TOA5_CatTien_EC_2012_02_16_0130.dat)

    Actually, I want the program will been not interrupted because I have plan to run it for 12 months data. As you know, the result with flags is available if data is not good and we could make gap filling this result.

    Thanks again and best regards,

    Duy Dinh,

    #1747

    duydb.vrtc
    Participant

    Hello gerardo,

    Thank you very much for your support. I have just run with your metadata file and It’s Ok with 4 my sample file (TOA5_CatTien_EC_2012_02_15_2300.dat -> TOA5_CatTien_EC_2012_02_16_0030.dat). However, The program has been interrupted when I try to run with more other file.

    Please run again with my 6 file (TOA5_CatTien_EC_2012_02_15_2300.dat -> TOA5_CatTien_EC_2012_02_16_0130.dat)

    Actually, I want the program will been not interrupted because I have plan to run it for 12 months data. As you know, the result with flags is available if data is not good and we could make gap filling this result.

    Thanks again and best regards,

    Duy Dinh,

Viewing 4 posts - 1 through 4 (of 4 total)

You must be logged in to reply to this topic.

Comments are closed.