| BiometPackage |
100 |
Sensor package identifier (100, 101, 102, or 103). |
| AveragePeriod |
60 |
Time period over which to average sensor data in seconds. |
| ScanInterval |
5 |
How often to sample the sensors in seconds. Note that the HydraProbes require a 3-second warm up before each
sampling event. |
| UsePublicVars |
0 |
Flag to set raw variables as public or not: 1 = public, 0
= not public |
LogBiomet
Data |
9999 |
Number of records to keep in Biomet data table. |
LogControl
Flags |
1 |
Number of records to keep in ControlFlags
data table. |
| SHF1Sens |
60.01 |
Sensitivity for soil heat flux plate 1 in uV/W/m2 (unique value for each
soil heat flux plate). |
| SHF2Sens |
60.01 |
Sensitivity for soil heat flux plate 2 in uV/W/m2 (unique value for each
soil heat flux plate). |
| SHF3Sens |
60.01 |
Sensitivity for soil heat flux plate 3 in uV/W/m2 (unique value for each
soil heat flux plate). |
| SHF1RSelf |
100.01 |
Self-resistance for soil heat flux plate 1 in Ohms (unique value for each soil heat flux plate). |
| SHF2RSelf |
100.01 |
Self-resistance for soil heat flux plate 2 in Ohms (unique value for each soil heat flux plate). |
| SHF3RSelf |
100.01 |
Self-resistance for soil heat flux plate 3 in Ohms (unique value for each soil heat flux plate). |
| CompResistor |
10.01 |
Resistance of the completion resistors used with
self-calibrating soil heat flux plates in Ohms. |
| CalDuration |
3 |
How many minutes to actively heat the soil heat flux
plates during calibration. |
| CalInterval |
6 |
How often to calibrate self-calibrating heat flux plates
in hours. |
| SoilType |
3 |
Soil type ID: 1 = sand, 2 = silt, 3 = clay, 4 = loam. |
HydraStart
Address |
1 |
Address of the first HydraProbe. Note that the program can accommodate up to 3 HydraProbes
using sequential addresses. |
HydraStop
Address |
3 |
Address of the last HydraProbe. |
| LI190Mult |
-200.01 |
Multiplier for the LI-190 or LI-190R. |
| LI200Mult |
-100.01 |
Multiplier for the LI-200 or LI-200R. |
Pyranometer
UpSens |
15.01 |
CNR4 upper pyranometer sensitivity (unique
value for each net radiometer). |
| Pyranometer DownSens |
15.01 |
CNR4 lower pyranometer sensitivity (unique
value for each net radiometer). |
Pyrgeometer
UpSens |
8.01 |
CNR4 upper pyrgeometer
sensitivity (unique value for each net radiometer). |
Pyrgeometer
DownSens |
8.01 |
CNR4 lower pyrgeometer
sensitivity (unique value for each net radiometer). |
| CNR4Shunt |
1000 |
Resistance of the CNR4 temperature sensor shunt resistor
in Ohms. |
| HeatStartTime |
20:00 |
Turn on time for the optional CNF4 heater. |
| HeatStopTime |
08:00 |
Turn off time for the optional CNF4 heater. |
| VentStartTime |
20:00 |
Turn on time for the optional CNF4 ventilator. |
| VentStopTime |
08:00 |
Turn off time for the optional CNF4 ventilator. |
