The table below shows the control that can be set via SETCONTROL
| Type | Group | Name | Description |
|---|---|---|---|
| Auxiliary | Analog | AuxPwr | Voltage for the auxiliary power port in head |
| Dac1 | D/A #1 (pin 2) setting | ||
| Dac2 | D/A #2 (pin 3) setting | ||
| Dac3 | D/A #3 (pin 4) setting | ||
| Dac4 | D/A #4 (pin 5) setting | ||
| Digital | ADC1Pullup | ADC Channel 1 pullup (pin 21) | |
| Dio1 | Digital I/O port 1 (pin 6) | ||
| Dio2 | Digital I/O port 2 (pin 7). | ||
| Dio3 | Digital I/O port 3 (pin 8). | ||
| Dio4 | Digital I/O port 4 (pin 9). | ||
| Dio5 | Digital I/O port 5 (pin 10). | ||
| Dio6 | Digital I/O port 6 (pin 11). | ||
| Dio7 | Digital I/O port 7 (pin 12). | ||
| Dio8 | Digital I/O port 8 (pin 13). | ||
| Excite5 | 5V Excitation (pin 25). | ||
| Power12 | 12V Power (pin 23). | ||
| Power5 | 5V Power (pin 14). | ||
| Constants | Fluorometry | FLR:Adark | Dark photosynthetic rate |
| FLR:Fm | Value of dark adapted Fm | ||
| FLR:Fo | Value of dark adapted Fo | ||
| FLR:PS2/1 | Photosystem distribution factor | ||
| Gas Exchange | Const:Geometry | Leaf type | |
| Const:Custom | 1-sided BLC for custom | ||
| Const:K | Stomatal ratio | ||
| Const:S | Leaf area | ||
| Leaf Temp | LTConst:deltaTw | Wall temperature difference from air temp (for energy balance) | |
| LTConst:fT1 | Fractional contribution of leaf thermocouple T1 | ||
| LTConst:fT2 | fractional contribution of leaf thermocouple T2 | ||
| LTConst:fTeb | Fractional contribution of leaf energy balance | ||
| Soil | Soil:#Reps | Soil measurement rep count per measurement | |
| Soil:CircPump_% | Circulation pump speed | ||
| Soil:Duration | Soil measurement duration | ||
| System | SysConst:AvgTime | System average time | |
| SysConst:Oxygen | Oxygen concentration | ||
| User Defined | User:myfirst | ||
| User:mysecond | |||
| Env Controls | CO2 | CO2 On/Off | CO2 Controller on/off |
| CO2_% | CO2 injector setting (0-100) | ||
| CO2_r | Reference CO2 control setpoint | ||
| CO2_s | Sample CO2 control setpoint | ||
| Color | Color_All | Color specifier for all sensors | |
| Color_Con | Color specifier for light source attached to console | ||
| Color_Flr | Color specifier for fluorometer | ||
| Color_Head | Color specifier for light source attached to head | ||
| Color_Qin | Color specifier for all sensors contributing to the leaf | ||
| Fan | Fan On/Off | Fan Controller on/off | |
| Fan_% | Fan speed power (0=off, 100=full) | ||
| Fan_blc | Boundary layer conductance setpoint (controlled by fan speed) | ||
| Fan_rpm | Fan speed setpoint | ||
| Flow | Flow | Flow rate to chamber | |
| Flow On/Off | Flow Controller on/off | ||
| Flow_% | Flow split setting (% to leaf chamber) | ||
| Pump | Pump speed setting | ||
| H2O | Desiccant_% | Direct control of desiccant tube (0=bypass, 100=full scrub) | |
| H2O_On/Off | H2O Controller on/off | ||
| H2O_% | Direct H2O control from full dry (-100) to full humidity (100) | ||
| H2O_r | H2O Reference setpoint | ||
| H2O_s | H2O Sample setpoint | ||
| Humidifier-% | Direct control of humidifier tube (0=bypass, 100=full wetting) | ||
| RH_air | Chamber relative humidity setpoint | ||
| SD_air | Saturation Deficit (air) setpoint | ||
| VPD_leaf | Vapor Pressure Deficit (leaf) setpoint | ||
| Light | Q_All | All light source(s) setpoint | |
| Q_Console | Light source attached to console setpoint | ||
| Q_Flr | Fluorometer actinic setpoint | ||
| Q_Head | Light source attached to head setpoint | ||
| Qin | Light incident on leaf setpoint | ||
| Pressure | Pressure | Chamber over-pressure pressure setpoint | |
| Pressure_On/Off | Pressure Controller on/off | ||
| Pressure_% | Chamber over-pressure control setting | ||
| Temp | Tair | Chamber air temperature setpoint | |
| Temp_On/Off | Temp Controller on/off | ||
| Tleaf | Leaf temperature setpoint | ||
| Txchg | Heat exchanger setpoint | ||
| Flr Settings | Dark | DARK:After | Far red off time after actinic off |
| DARK:Before | Turn far red on time prior to actinic off | ||
| DARK:Duration | Dark pulse duration | ||
| DARK:FarRed target | Dark pulse far red target | ||
| Induction | IND:Duration | Induction flash duration | |
| IND:Red target | Induction flash red target | ||
| MPF | MPF:Phase 1 | MPF phase 1 duration | |
| MPF:Phase 2 | MPF phase 2 duration | ||
| MPF:Phase 3 | MPF phase 3 duration | ||
| MPF:Ramp | MPF ramp control | ||
| MPF:Red target | MPF red target value | ||
| Measure | Meas:AverageTime | Averaging time for Fs and Fs’ | |
| Meas:DarkModRate | Modulation rate for dark measurements | ||
| Meas:FlashModRate | Modulation rate during flash events | ||
| Meas:LightModRate | Modulation rate for light measurements | ||
| Meas:Modulation | Modulation control: | ||
| Meas:Recording | Turn flr recording on/off | ||
| RF | RF:Duration | Rectangular flash duration | |
| RF:Red target | Rectangular flash red target value | ||
| Log Options | Flr | FlrOpt:Action | Fluorometer Action at Log |
| FlrOpt:Auto | Threshold for Automatic MPF | ||
| FlrOpt:FlashType | Fluorometer Flash Type | ||
| FlrOpt:MinFlash | Minimum flash interval | ||
| Match | MchOpt:CO2Change | Match if CO2_r changed > | |
| MchOpt:CO2Delta | Match if |CO2_r - CO2_s| < | ||
| MchOpt:Choice | Match when logging? | ||
| MchOpt:Elapsed | Match if elapsed time by | ||
| MchOpt:H2ODelta | Match if |H2O_r - H2O_s| < | ||
| MchOpt:H2OChange | Match if H2O_r changed > | ||
| Std | LogOps:MakeExcel | Also create Excel log file | |
| LogOpts:AvgTime | Additional averaging time | ||
| LogOpts:Beep | Beep on log | ||
| Misc | Match Mode | Mch:AvgTime | Auto match stats averaging time |
| Mch:CO2 limit | CO2 delta rate of change green light threshold | ||
| Mch:H2O limit | H2O delta rate of change green light threshold | ||
| Mch:Mode | Match mode action | ||
| Mch:Timeout | Auto mode timeout time | ||
| Power Settings | PowerState | Sleep/Standby mode control |
